考虑制动力影响的大型客车舒适性分析

利用有限元法和动力平衡原理,建立了具有层间接触的沥青路面和13个自由度的大型客车人体三维模型。以不平顺作为激励,随机模拟车流分布,在不同制动情况下,从时域和频域两方面分析人-车-路耦合振动下车辆和人体的动力响应。时域分析采用客观评价标准和主观烦恼率相结合的方法,频域分析考虑人体共振、人的心理和生理因素。结果表明:随着制动力增大,人体的竖向加速度幅值不变,俯仰、侧倾加速度幅值都增大,但是俯仰加速度增幅远大于侧倾加速度的情况,人的舒适性变差,烦恼率增高;在紧急制动时,主频段对人体共振、心理和生理产生的影响很小,但是次主频段与人体某些器官固有频段重合,对人体共振、心理和生理产生的影响是不容忽视的。     

AlGaN/GaN高电子迁移率器件外部边缘电容的物理模型

AlGaN/GaN HEMT外部边缘电容Cofd是由栅极垂直侧壁与二维电子气水平壁之间的电场构成的等效电容.本文基于保角映射法对Cofd进行物理建模,考虑沟道长度调制效应,研究外部偏置、阈值电压漂移和温度变化对Cofd的影响:随着漏源偏压从零开始增加,Cofd先保持不变再开始衰减,其衰减速率随栅源偏压的增加而减缓;AlGaN势垒层中施主杂质浓度的减小和Al组分的减小都可引起阈值电压的正向漂移,正向阈值漂移会加强沟道长度调制效应对Cofd的影响,导致Cofd呈线性衰减.在大漏极偏压工作情况下,Cofd对器件工作温度的变化更加敏感.     

Tightly coupled aeroelastic model implementation dedicated to fast aeroelastic tailoring optimisation of high aspect ratio composite wing

This paper presents the development of a code, called GEBTAero, dedicated to very flexible aircraft (VFA) aeroelasticity and especially the evaluation of aeroelastic tailoring effect on critical speeds. GEBTAero is an open source code consisting in a tightly coupling between a geometrically exact beam theory -and a finite state induced flow unsteady aerodynamic model, including an homogenisation tool. This model has been implemented in Fortran using GEBT code and optimised open source libraries with particular focus on computation speed. Besides a non linear transient dynamic simulation capacity, a particular focus is put on the fast critical speed computation strategy using a non-iterative modal approach about the geometrically non linear deformed shape of the wing with the computation of only a few aeroelastic modes. Computation speed and accuracy of this implementation is assessed using widely used aeroelastic test cases and compared successfully to other aeroelastic codes. Configurations using aeroelastic tailoring, which are the core target of this solver, are then evaluated numerically on a representative high aspect ratio anisotropic composite wing and a simple 2-ply composite laminates with both variable ply orientations. It illustrates the strong correlation between the structural bending/twisting coupling of an unbalanced composite laminates and its critical aeroelastic speed. It also shows the high sensitivity of ply orientation on the aeroelastic behaviour.     

Fundamental solution of steady oscillations in thermoelastic medium with voids

ABSTRACT

The article deals with the study of plane wave propagation in the thermoelastic medium in the presence of voids. The problem is considered in the context of three-phase-lag model of generalized thermoelasticity. There exists three longitudinal waves, namely elastic (E-mode), thermal (T-mode) and volume fraction (V-mode) in addition to transverse waves which get decoupled from the rest of motion and not affected by thermal and volume fraction fields. The fundamental solution of the system of differential equations in case of steady oscillations in terms of the elementary functions has been constructed. The phase velocity and attenuation coefficient of these waves are computed numerically and presented graphically.     

On the nature of phase separation of polymer solutions at high extension rates

Experiments with stretching moderately concentrated polymer solutions have been carried out. Model experiments were carried out for poly(acrylonitrile) solutions in dimethyl siloxane. Just the choice of concentrated solutions allowed for a clear demonstration of a demixing effect with the formation of two separate phases—an oriented polymer fiber and solvent drops sitting on its surface. An original experimental device for following all subsequent stages in the demixing process was built. It combined two light beams, one transverse to the fiber and a second directed along (inside) the fiber, the latter played the role of an optical line. This gives a unique opportunity to observe processes occurring inside a fiber. The process of demixing starts from the volume phase separation across the whole cross section of a fiber at some critical deformation and the propagation of the front of demixing along the fiber. Then a solvent cylindrical skin appears which transforms into a system of separate droplets. New experimental data are discussed based on a comparison of the current different points of view on the phenomenon of deformation‐induced phase separation: thermodynamic shift of the equilibrium phase transition temperature, growth of stress‐induced concentration fluctuations in two‐component fluids, and mechanically pressing a solvent out from a polymer network. The general belief is that a rather specific (so‐called “beads‐on‐a‐string”) structure of a filament is realized in stretching dilute solutions: beads of a polymer solution connected by oriented polymer bridges forming a single object. The situation in stretching moderately concentrated solutions appears quite different: real phase separation was observed. So, the alternative phenomenon to the formation of the “beads‐on‐a‐string” structure has been experimentally proven. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 559–565     

超音速等离子体炬的磁流体动力学数值研究

针对设计的喉径2mm、工作电流为100A的拉瓦尔喷嘴,在二维轴对称模型的基础上,对超音速等离子体炬中的流动及其外部射流进行了数值模拟。通过在阳极喷嘴内部采用基于磁矢量势的磁流体动力学模型,避免了对磁感应强度的复杂积分计算,得到了喷嘴内部多场耦合的结果及外部射流的流动状态,分析了喷嘴内部电磁场对等离子体的加速作用及射流发展过程。结果显示,等离子体经历了亚音速→跨音速→超音速的发展过程,最终获得2.3 Ma的超音速射流。研究结果为超音速等离子体炬的工业应用提供了理论基础。     

Mechanism of [3+2] Cycloaddition of Alkynes to the [Mo3S4(acac)3(py)3][PF6] Cluster

A study, involving kinetic measurements on the stopped‐flow and conventional UV/Vis timescales, ESI‐MS, NMR spectroscopy and DFT calculations, has been carried out to understand the mechanism of the reaction of [Mo₃S₄(acac)₃(py)₃][PF₆] ([ 1 ]PF₆; acac=acetylacetonate, py=pyridine) with two RC?CR alkynes (R=CH₂OH (btd), COOH (adc)) in CH₃CN. Both reactions show polyphasic kinetics, but experimental and computational data indicate that alkyne activation occurs in a single kinetic step through a concerted mechanism similar to that of organic [3+2] cycloaddition reactions, in this case through the interaction with one Mo(μ‐S)₂ moiety of [ 1 ]⁺. The rate of this step is three orders of magnitude faster for adc than that for btd, and the products initially formed evolve in subsequent steps into compounds that result from substitution of py ligands or from reorganization to give species with different structures. Activation strain analysis of the [3+2] cycloaddition step reveals that the deformation of the two reactants has a small contribution to the difference in the computed activation barriers, which is mainly associated with the change in the extent of their interaction at the transition‐state structures. Subsequent frontier molecular orbital analysis shows that the carboxylic acid substituents on adc stabilize its HOMO and LUMO orbitals with respect to those on btd due to better electron‐withdrawing properties. As a result, the frontier molecular orbitals of the cluster and alkyne become closer in energy; this allows a stronger interaction.     

PN结物理特性的开放式测量实验方法研究

开放式、综合性量测实验的设计与应用,在巩固基础理论知识的同时,能够有效培养学生的动手实践能力、数据处理及分析能力,一定程度代表着大学物理实验课程的教学模式改革方向。以PN结物理特性的测量实验为例,基于通用型仪器与元器件的积木式组合,设计出简单、适用的实验电路;t=17.95℃时所采集的原始实验数据经三种模式回归分析,比较验证了PN结扩散电流与电压间遵循的玻尔兹曼分布律;计算出的玻尔兹曼常数与FD-PN-4测定仪的量测值相比,其结果说明了开放式测量实验方法的有效性。     

A modern approach to the solution and analysis of the Simha-Somcynsky model for the description of pressure-volume-temperature properties of polymer fluids

We revisit the Simha-Somcynsky model of polymer fluids with the purpose of developing novel theoretical and computational approaches to simplify and speed up its solution as well as the fitting of experimental data, and decrease its level of mathematical complexity. We report a novel method that allows us to solve one of the two equations of the model exactly, thus putting the level of mathematical difficulty on a par with the one of other models for polymer fluids. Moreover, we describe a computational algorithm capable of fitting all five parameters of the model in an unbiased way. The results obtained reproduce literature results and fit experimental pressure-volume-temperature and solubility parameter data for three polymers very accurately. Moreover, the new techniques allow for the investigation of the model at very low temperatures. Unexpectedly, the model predicts behaviors that could be interpreted as a glass transition, as routinely observed in dilatometry and differential scanning calorimetry, and a glass phase. We compared the predicted and experimental T g’s for cis poly(1,4-butadiene) and found an excellent quantitative agreement.